Parts for Kenmore Models 8433A REV A

Silverware basket - gray (basket, silverware (gray))

This is a basket for washing flatware or silverware in your dishwasher. It is located on the lower rack. If your silverware basket is damaged or worn out, you should replace it. No tools are required for this repair. This gray basket is a genuine OEM part.

Easy Part #:: EAP11743069

Availability:: In Stock

Price:: $25.82

Door balance link kit (dishwasher door spring cable kit)

The door balance kit helps support the weight of the dishwasher door while it opens and closes. If the spring to the door is damaged/broken or the door is not opening and closing properly you will need to replace this part. This door kit includes 2 door balance links and 2 door balance mounts with wheels for the left and right side of the door. This is a genuine OEM part.

Easy Part #:: EAP972325

Availability:: In Stock

Price:: $27.90

Rack track stop (track, stop non-removable)

This gray rack track stop is used for your upper dish rack track to prevent the rack from sliding off the slide rail. If your rack is falling off the track, you may need to replace the track stop. This is a genuine OEM part and is sold individually.

Easy Part #:: EAP11746591

Availability:: In Stock

Price:: $10.33

Dryer cycling thermostat (thermostat, internal-bias)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741405

Availability:: In Stock

Price:: $23.85

M series new style coil kit (sub 12001349)

This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two-terminal secondary coil. If there is no heat or your drying time is getting longer, the coils may be bad and will need to be replaced. Once the coils go bad they do not hold the gas valve open properly. Usually only one of them burns out but you should replace them as a set. Both must be operational for the gas valve to open. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334310

Availability:: In Stock

Price:: $26.40

Agitator repair kit (cam-agit)

This agitator repair kit is used to move the upper agitator and connects the base of the agitator with the agitator top mover. The kit is most commonly used if the top part of the agitator is not moving correctly but the bottom portion is. If your washer will not agitate or is noisy, you may need to replace the kit. The kit includes a medium cam, agitator dogs, bearing, thrust bearing washer, and a dust cap seal. Agitator grease is recommended for the repair, but it is not included with the agitator repair kit, it must be ordered separately. This is a genuine OEM part. Please remember to disconnect the power and water supply to the washer before starting your repair.

Easy Part #:: EAP334650

Availability:: In Stock

Price:: $23.00

Rear drum support roller kit (use wpl 349241t)

This drum support roller kit is used for square-ported model clothes dryers. It has a metallic bearing in its center. This support roller is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble, or takes too long to dry you might need to replace the roller. The kit is a genuine OEM kit and it includes two drum support rollers, four tri rings, and one retaining washer. It is recommended that you replace both rollers at once. Please remember to disconnect the power to your appliance before starting your repair.

Easy Part #:: EAP347627

Availability:: In Stock

Price:: $13.37

Rear drum bearing kit (shaft)

This rear drum bearing kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws. The support bearing helps support the dryer drum to rotate quietly and smoothly during operation. The bearing attaches on the inside of the rear panel of the dryer cabinet. Over time the drum bearing will wear out. This kit will help keep your dryer running as smoothly as possible with as little noise as possible. This is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:: EAP459829

Availability:: In Stock

Price:: $52.07

Crisper drawer cover (cover pan low)

This crisper drawer cover has the drawer slides built into it to allow the crisper drawer to slide in and out. This model measures 24 1/2 inches long x 19 inches wide x 2 5/8 inches deep, is made of plastic and is white in color. If the cover becomes cracked or damaged, you will need to replace it. This is a genuine OEM part.

Easy Part #:: EAP890565

Availability:: In Stock

Price:: $70.79

Replacement ice maker (refrigerator ice maker)

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Easy Part #:: EAP358591

Availability:: In Stock

Price:: $111.50

Belt kit (pump belt - 40.5 inches long)

There are two belts under a Maytag washer; one for the main drive pulley and one for the water pump. The belt kit includes both the drive belt and the pump belt which are both V-shaped. The belt connects the drive motor to the drive system to be able to spin the tub basket. If your washer will not agitate, not spin, or not drain, the belt could be worn or damaged and will need to be replaced. This is a genuine OEM kit. Please remember to disconnect the power and shut off the water supply to your washer before starting your repair.

Easy Part #:: EAP2005284

Availability:: In Stock

Price:: $37.07

Door catch kit (use wpl 279570)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Easy Part #:: EAP334230

Availability:: In Stock

Price:: $4.02

Upper rack wheel with mount (dishwasher dishrack roller assembly, upper)

This wheel and mount assembly is located on the upper dishwasher rack to allow you to slide the rack in and out easily. They are sold individually; four are usually required for your model. Also known as stationary wheel mount. This is a genuine OEM part.

Easy Part #:: EAP11745451

Availability:: In Stock

Price:: $23.26

Suspension spring

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Easy Part #:: EAP11743345

Availability:: In Stock

Price:: $7.07

Upper roller and axle - kit of 4 (dishwasher dishrack roller kit, set of 4. These rollers allow the dishrack to move in and out of the dishwasher.)

The upper roller and axle attach to the upper rack to allow the dishrack to move in and out along the track of the dishwasher. This is a kit includes 4 rollers and 4 axles for your upper rack. If your dish rack is not moving in and out of the dishwasher properly you may have a broken or missing wheel and it will need to be replaced. The rollers and axles are made out of plastic and are white in color. This is a genuine OEM kit.